Search found 1223 matches

by lottoarchitect
Sat Feb 15, 2020 12:52 pm
Forum: General Discussion
Topic: Tutorial - Typical usage examples of GAT Engine
Replies: 0
Views: 1675

Tutorial - Typical usage examples of GAT Engine

This question comes up regularly, so it could be a good idea to post some general usage ideas of this program. 1) The default and original operation is the use of Run Factor. This mode is applicable in all panorama modes. The idea is to pick a GAT which demonstrates good desired qualities. The reali...
by lottoarchitect
Sun Feb 09, 2020 11:56 pm
Forum: General Discussion
Topic: History Performance in original order too
Replies: 10
Views: 1698

Re: History Performance in original order too

Generally speaking the GAT application will provide better results overall. The online system is a best effort attempt to make scans in a limited time to make results available. It would be strange if it was the other way around. I cannot suggest what settings to use in GAT as is. Given each game is...
by lottoarchitect
Sat Feb 08, 2020 10:01 pm
Forum: News - Announcements
Topic: New Wheel Generator 1.8.5.1 and GAT Engine 3.0.2 versions
Replies: 0
Views: 1652

New Wheel Generator 1.8.5.1 and GAT Engine 3.0.2 versions

New versions of these programs were made available today. The changes mostly include known bug-fixes. Most notably, we hopefully have addressed this error message "Ordinal X not found" which shows up on some installations. Please let us know if you had that error and if it is gone after this update....
by lottoarchitect
Fri Feb 07, 2020 10:55 am
Forum: General Discussion
Topic: Filter when k <> m
Replies: 7
Views: 1552

Re: Filter when k <> m

This has been already answered at my first reply, the logic behind these constructions. If it can be made or not, entirely depends on what blocks are allowed or not by the filters. One quick way to see if it can be made to 100% is to add quite more blocks than needed for the unconditional case. This...
by lottoarchitect
Thu Feb 06, 2020 6:12 pm
Forum: General Discussion
Topic: Filter when k <> m
Replies: 7
Views: 1552

Re: Filter when k <> m

Correction for your post, you mention C (10,6,5,6) = 14 Yes this definitely can be reduced with FD % given M=K. What you care about is to reach FD to 100% (also enable the check box filtered over overall). Unconditional coverage obviously will not be at 100% but the assumption here is your guide fil...
by lottoarchitect
Thu Feb 06, 2020 6:07 pm
Forum: General Discussion
Topic: Filter when k <> m
Replies: 7
Views: 1552

Re: Filter when k <> m

A requirement to be able to evaluate the FD % is to have M=K. Under that condition, you can reduce blocks from an unconditional 100% cover, like the C (10,6,5,6) = 14 with the introduction of additional filters (guide/mother), similar to the initial M condition. It is impossible to reduce blocks via...
by lottoarchitect
Thu Feb 06, 2020 1:43 pm
Forum: General Discussion
Topic: History Performance in original order too
Replies: 10
Views: 1698

Re: History Performance in original order too

At its current implementation it scans augmentative tables just like what GAT 3.0 delivers with the inclusion of internally used Hits+Delay information. As it goes through each produced GAT table, it picks it as the current candidate if that table results in more total hits production + Hits/delay s...
by lottoarchitect
Thu Feb 06, 2020 1:09 pm
Forum: General Discussion
Topic: Filter when k <> m
Replies: 7
Views: 1552

Re: Filter when k <> m

Hi ccampos, whenever you introduce a filter in guide mode (or use a mother), you introduce the possibility one particular combination that is necessary to make an 100% unconditional cover unavailable. Ability to make an 100% unconditional cover using guide filters is completely dependent on the bloc...
by lottoarchitect
Tue Feb 04, 2020 10:47 pm
Forum: General Discussion
Topic: History Performance in original order too
Replies: 10
Views: 1698

Re: History Performance in original order too

What do you mean public?
by lottoarchitect
Fri Jan 31, 2020 5:04 pm
Forum: General Discussion
Topic: History Performance in original order too
Replies: 10
Views: 1698

Re: History Performance in original order too

The online system operates in a different manner to GAT. It uses the same building blocks (the GAT tables) and attempts to combine various results from them. This approach is what I suggested to end up in GAT as the automatic mode. So, no it will not work suggesting settings used by the online syste...